coleman 5600 gas grill manual

LOOSELY assemble two additional Screws (TN) and two Flat Washers (DY) through the Firebox into the Right Side Table at the rear of the grill. Assemble Left Fryer Step Assembly to the Grill. 11-A Left Fryer Assembly Left Rear Panel 11-B Hardware shown actual size (TN) M6 x 15mm Screw (1) Qty. 11-A. Raise the Grill Lids. Place the Left Fryer Assembly against the Firebox and on top of the Left Rear Panel. Step 12-A 12-C View of Grill from Rear Hardware shown actual size (TN) (DY) M6 x 15mm Screw M6 Flat Washer (4) Qty. (2) Qty. 12-A. LOOSELY assemble two additional Screws (TN) and two Flatwashers (DY) through the Firebox into the Left Fryer Assembly at the rear of the grill. Step Assemble the Grease Pan below the Fryer Burner. 14-A Route the Electrode Wire through the slot in the Electrode Tip 14-A. Attach the Electrode Wire to the Electrode Tip on the Side Fryer. 14-B Hooks 14-B. NOTE: Place the Fryer Heat Shield between the Fryer Panel and the Flexible Fuel Hose. Do not pinch Electrode Wire. Engage the two tabs on the Heat Shield downward into the rectangle holes. 15-B Fryer Heat. Wrap the Wire Tie around the wire and secure in place. Route the Electrical Wires under the Right Side Table. Step 17-A 17-A. Firmly push the Electrode Wires into the Electrode Module.Step Hardware shown actual size (VP) Self Tapping Screw (2) Qty. 18-A FIREBOX 18-B 18-C REAR TRIM PLATE VP (x2) 18-C. View showing Rear Trim Plate properly installed. 18-A. Fasten the Rear Trim Plate to the Firebox with. Attach the Tool Hook to the Step Right Door. 19-A LEFT DOOR (without Tool Hook Brackets) 19-B 19-B. Fasten the Right Door to the Grill Cart with four Flat Head Screws (XR). NOTE: Right Door has Tool Hook Brackets. Attach the Tool Hook to the Step Right Door. NOTE: M4 x 5mm Screws are factory installed into the Handles. Hardware shown actual size (EZ) M4 X 5mm Screw (4) Qty. 20-A EZ (x2) RIGHT DOOR DOOR. Locate the Power Grates in the center positions. 21-D Warming Racks.

• coleman 5600 gas grill manual, coleman 5600 gas grill manual instructions, coleman 5600 gas grill manual download, coleman 5600 gas grill manual pdf, coleman 5600 gas grill manual free.

Keep this manual for To check local codes, see your local L.P. It is important that there are no leaking connections on your gas grill that could cause a fire or explosion (see “LEAK TESTING”, Pg. 32). Gas is under high pressure.NOTE: The base pieces are assembled up-side- Step down in this step. Hardware shown actual size (TN) M6 x 15mm Screw (8) Qty. Engage the Locking Step Casters to prevent movement during the rest of the assembly process. 2-A. Assemble the Cylinder 2-B. Assemble the Cylinder Hardware shown actual size (VP) Self Tapping Screw (1) Qty. Cylinder Support Retaining Bolt to the Hardware shown actual size Cylinder Support. Step Cart Spacer View of Grill from Rear View of Grill from Rear TN (x8) Cart Spacer Cart Spacers Hardware shown actual size (TN) M6 x 15mm Screw (8) Qty. 4-A. Assemble two Cart Spacers between the Left and Right Panels using eight Screws (TN). Hardware shown actual size Step Rear Panel 5-A. Assemble two Rear Panels to the cart assem- bly using eight Screws (TN). NOTE: The Rear Panels are identical. Align the square holes on the Rear Panel with the tabs and push down to install the panels. NOTE: A second person is Step needed when aligning the Firebox to the Grill Cart. 7-A. Carefully place the Firebox onto the Cart Assembly. Do not damage the Electrical Wires (see Fig. 7-B and 7-C). The Electrical Wires must be routed through the openings near the front and back of the Firebox. TN (x2) DY (x2) Flange on Right Side Panel 8-B. Fasten the left side of the Firebox to the Grill Cart with two Flat Washers (DY) and two Screws (TN). Tighten all fasteners. Right Side Firebox Table Right Rear Panel Hardware shown actual size (TN) M6 x 15mm Screw (4) Qty. 9-A. Raise the Grill Lids. Place the Right Side Table against the Firebox and on top of the Right Rear Panel. Step 10-A 10-C DY (x2) View of Grill from Rear Hardware shown actual size (TN) (DY) M6 x 15mm Screw M6 Flat Washer (4) Qty. (2) Qty. 10-A.

Page 2 Contents WARNINGPage 4 Electrical Attachments Fuel Connections Other ThanFilling and Purging Type 1Left Fryer. Assembly. Page 8 O NOTE: Use a large piece of cardboard or a groundPage 9 O Carefully turn the assembly O Assemble the Right SidePage 10 O Assemble two Cart Spacers Hardware shown actual sizeO Install Door Magnets.Page 15 O Assemble Right Side Table Hardware shown actual sizePage 17 O Assemble Left Fryer Hardware shown actual sizeStep O Assemble the Grease Pan. Page 20 O Assemble Front Fryer HeatO Install two Grease. Page 28 O Assemble the Motor Mount 25-C NOTE:Page 31 O NOTE: Step 27 applies to you only if your grill is set up from the factory to use NATURAL. Page 32 Connecting Type 1 L.P. Gas Cylinders Leak Testing (cont.)Page 33 Fixing A Fuel Leak (cont.) Lighting InstructionsPage 34 Lighting Main Burners Fryer Burner Lighting. Igniter LightingPage 35 General Use and Correct Burner Flames Grilling Tips and HintsPage 38 Troubleshooting cont. For Your Additional Safety cont.Page 39 ATTN: DEPT 586First-ClassPage 41 Recipes. Spice-rubbed spareribs Grilled tuna steaks with olive vinaigrette. Cooking time: 45 minutes to partial boil; 16-20 min- Cooking time. Page 42 Recipes. Asian-flavored eggplant Chili-orange pork loin. Cooking time: 8-10 minutes Cooking time after marination: 6-7 minutesPage 43 Recipes. Lemongrass beef skewers with peanut dipping Lamb grilled with rosemary and DijonPage 44 Warranty. Keep this manual for future reference. If you have questions about assembly, operation, servicing or repair of this grill, please call Coleman at 1-800-835-3278 or TDD: 316-832-8707. In Canada call 1-800-387-6161. Very often issues with Coleman 5600 begin only after the warranty period ends and you may want to find how to repair it or just do some service work. Even oftener it is hard to remember what does each function in Gas Grill Coleman 5600 is responsible for and what options to choose for expected result.

Note: The Grease Pan is shown Step up-side-down during this step. Hardware shown actual size Self Tapping Screw 23-A VP (x4) Grease Support Grease Pan Note: Lip is up. 23-A. Attach the Grease Cup Support to the Grease Pan with two self-tapping screws (VP). Step Assemble the Rotisserie to the Firebox. Hardware shown actual size (TN) M6 x 15mm Screw (2) Qty. 25-A UO (x2) Motor Mount Bracket 25-A. Attach the Motor Mount Bracket to the metal side panel using two Screws (TN) and two Hex Nuts (UO). Damage will occur if the Handle is not removed prior to cooking.If your grill is set up from the factory to use NATURAL GAS, skip to Step 27. Attach an LP Cylinder to the Grill. If your grill is set up from the factory to use LP GAS, skip back to Step 26. Attach a NATURAL GAS line to the grill. DO NOT attempt to repair the cylinder valve if it should become damaged;. If there are cuts, damage, excessive abrasion or wear, replace the hoses prior to operating the appliance.Locate your nearest service center by calling 1-800-835-3278. Use care when moving a portable gas grill. DO NOT run with or pull the grill behind you;. PROMOTE BETTER PRODUCTS: We value your input. Your responses will help us develop products designed to best meet your needs. Your answers are important to us.Coleman, at its option, will repair or replace this product or any component of the product found to be defective during the war- ranty period. Repair your BBQ today. Keep this manual for future reference. If you have questions about assembly, operation, servicing or repair of this grill, please call Coleman at 1-800-835-3278 or TDD: 316-832-8707. In Canada call 1-800-387-6161.Sign up now. Keep this manual for future reference. If you have questions about assembly, operation, servicing or repair of this grill, please call Coleman at 1-800-835-3278 or TDD: 316-832-8707. In Canada call 1-800-387-6161.

18): Lighting Instructions Rotisserie Control Knob Fryer Control Knob 34 Lighting Main Burners Shutting Off the Grill Lighting Rotisserie Burner Igniter Lighting Fryer Burner Lighting Igniter Lighting: 24b Fryer Control Knob Igniter Lighting Good Bad 21 Yellow Blue Holes in Burner Yellow Blue 35 Grilling Tips and Hints In Case of Grease Fire Follow These Steps: Note: General Use and Correct Burner Flames Condition The Grill The Burner Flame Burner Control Setting Tips Safe Grill Operation Steps For Cleaning Venturi: 36 Cleaning the Venturi Note: REPRESENTATIVE ILLUSTRATION Cooking Methods Side Fryer Cooking Methods Deep Fat Frying: The Side Fryer Option allows for several addi- tional cooking methods. Initial Start-up Notes: Frying Tips: Steaming: Warming: Direct Method: Indirect Method: 37 Moving and Storage Troubleshooting REPRESENTATIVE ILLUSTRATION Orifices Valves Problem: Burner will not light or has incomplete burner flame. Problem: Yellow flame. Problem: Grill too hot. Problem: Fire at any connection. Problem: Flame behind control panel or control knob area.Number of kids in household under 18 years of age: 18 Which best describes your family income? 13 2. Mrs. 3. Ms. 4. Marital Status: Number of people in household: 14 Education: (Check only one.) 8 Which factors most influenced your purchase? 9 Which of these best describes this purchase. Do you participate in any of the following activities? 10 17 What grill feature influenced the purchase of your Coleman grill? (Please check all that apply.) 19 Coleman Gas Barbecue Grill Limited Warranty 44 Warranty. Space-Gard, Universal Grill Parts, Chargriller, Ultragard Customer Review Price: Low to High Price: High to Low Using genuine Weber parts ensures your Weber grill will continue to last and perform like new.Features: Genuine Weber Part. Using genuine Weber parts ensures your Weber grill will continue to last and perform like new.Features: Genuine Weber Part.

Fortunately you can find all manuals for Gas Grill on our side using links below.Front Align the square Tighten all 5-A 6-B 5-B 6-A Install Rear Panels. Front 13 Fasten the Firebox to the 8-A 8-B LOOSELYfasten the Firebox to the NOTE: You will tighten these screws Tighten all fasteners. Assemble the Fuel Hose 13-A Fully insert the Male Hose Release the Collar to lock WARNING: 13-B 13-C 18 IMPORTANT! 19 Assemble the Electrode Assemble the Grease Pan 14-A 14-B NOTE: To attach the Fryer Grease Pan, raise the Pan slightly above the 23 Fasten the Rear Trim Plate 18-A NOTE: Route Tighten all 18-C 18-B 27 Assemble two Grease Cup 23-A 24-B Install the Grease Pan. Install two Grease Cups. 24-A After the Grease Cups are installed, push the Grease 28 Assemble the Motor Mount Assemble the Rotisserie to 25-A 25-C Place Slip Collar on Firebox Wall. Make sure Push Set Collar against the Slip Collar, provide Tighten the thumbscrews on the Set Collar 25-B 25-D 29 25-E Attach an LP Cylinder to the 26-A 26-B 26-C 30 IMPORTANT. WARNING: 31 Attach a NATURALGAS 32 Connecting Type 1 L.P. Gas Cylinders Leak Testing Leak Testing Fixing A Fuel Leak How to Check for Leaks 33 Fixing A Fuel Leak Start-Up Check List Control Knobs for Main Cooking Area Igniter Switch JKH REPRESENTATIVE ILLUSTRATION THE FOLLOWING RULES MUST ALWAYS BE FOLLOWED IN THIS ORDER (Fig.

Using this equipment with the respect and cautionThe following symbols shown below are used extensively throughout thisExtinguish any open flame. Open lid. If odor continues, immediately call yourNOT be stored in the vicinity of this or anyColds, allergies, sinus congestion, and the use of tobacco, alcohol or drugsGeneral Safety. Information cont.To check local codes, see your local L.P. gas dealer or natural gasThis appliance is not to be installed in or on a recreational vehicle. Follow these safety rules before each use:L.P. Gas CylinderLiquefied Petroleum gas (abbreviated L.P. gas or propane), isIt is importantPortable LP gas grills require a fuel delivery system which isThe valve assembly for this grill is ofYour new barbecue grill is equipped with a Type 1 coupling nut. This grill isCylinder SpecificationsA damaged valve can causeL.P. Gas Cylinder cont. Hose and Regulator. The Type 1 connection system has the following features:NOTE: The cylinder control valve must be turned off before anyA safety reliefThis will expel high pressure gas ifL.P. gas cylinders of the U. S. Department of Transportation. Cylinders, Spheres and Tubes for Transportation of Dangerous. Goods; and Commission, as applicable; and shall be providedThe pressure regulator and hose assembly with the Type 1 fittingDo not use anotherTransporting the CylinderHigh heat areas could cause the reliefFilling and Purging Type 1. L.P. Gas Cylinders cont.Gas is under high pressure.Failure to follow this information exactly could result in an. Purging and Evacuating Devices for L.P. Gas Cylinders with Type 1 Cylinder ValvesPOL plug into the valve outlet. Insertion of the plug will prevent the back-check from closing. Use ONLY the providedClose the cylinder valveFor proper purging procedures refer to. Procedures for Filling Cylinders”. Filling and Purging Type 1. L.P. Gas Cylinders. Take these instructions to the L.P. gas dealer.L.P. Gas industry procedures.

Failure to follow this instructionType 1 cylinder, be sure the exchanged cylinder is a Type 1Tell your L.P. GasThe L.P. Gas cylinder has a Type 1 cylinder valve with a backcheck module in its outlet which will not permit gas to flow untilTo purge the L.P. GasPurging can be accomplished using a hose end valveB. Hose end valve without a bleed port. When a hose end valve does not have a bleed port, a separateC. Purging using a Type 1 connection (Fig. 14). L.P. Gas cylinder evacuation can be accomplished during eachThe Type 1 valve outletStep 3Step 1Step 4. Right Lower Tank. Mounts. Step 2Tank Mounts andNOTE: GrillStep 5Connections andTo Set Up continued. Step 6. Step 7Right Side Shelf.Module. IMPORTANT: Always remove Lids in this order. Right Lid first. Left Lid second. Center Lid last.Channel, while at the same timeTurn cylinder valve knob counterclockwise (right to left) one rotation.Fig. 15. If bubbles appear at these areas, a leak is indicated.If you detect a leak:Push in and turn on control knobsColeman. DO NOT attempt to repair the cylinder valve if itWhen to test for leaks:Leak test anytime a part ofImmediately replaceIf there areDuring assembly ofLighting the GrillAttach to Grill. Read and follow directions on the cylinder and fuel hose safety tags.The connection requires about one-half to three-quartersTo disconnect, turnDO NOT use tools. Step 1Start-Up Check ListIt is especially important toNOTE: Follow this Lighting Procedure to light Burners on one side of theStep 2. L.P. gas cylinder.See that hoses have no kinks, sharp bends or tension. Insure that hoses are at least 3 inches away from anyStep 3NOTE: If the flame doesn’t immediately light, turn off control knobStep 3. Propane Cylinder Connection. L.P. gas cylinder and Lefthand Burner. NOTE: You must push Igniter ButtonStep 4Grease Pans. Match Lighting. Make sure all burner controls are off except one being lighted.Step 5. Step 1. OFF position. Step 2Step 10Step 11Step 8. IMPORTANT: Make sure Lid fits into.

Using genuine Weber parts ensures your Weber grill will continue to last and perform like new.Features: Genuine Weber Part Used to connect the. Using genuine Weber parts ensures your Weber grill will continue to last and perform like new.Features: Genuine Weber Part Used to connect the. Using genuine Weber parts ensures your Weber grill will continue to last and perform like new.Features: Genuine Weber Part. Using genuine Weber parts ensures your Weber grill will continue to last and perform like new.Features: Genuine Weber Part Used to connect the. Universal Gas Grill Replacement Control Knob for many brands of popular outdoor propane and natural gas bbq grills. Fits Great Outdoor Models: 1000, 6000, 6100, 7000, 7000H, 7000N, 7000W, 7500, 7500W, 8000, 8000N,. Using genuine Weber parts ensures your Weber grill will continue to last and perform like new.Features: Genuine Weber Part Fits. I had to modify my BBQ for it to fit properly, tubes in slightly wrong configuration.Found the same item for a lower price. The price does not violate any Minimum Advertised Pricing (MAP) requirement. Submit a request here, and we will get back to you as soon as possible. MAP Excluded Brands: Alfresco, Blaze, AOG, Artisan, Challenger, Delta Heat, FireMagic, Lynx, Napoleon, Rasmussen, Real Fyre, Sedona, Solaire, Summerset, TEC, Twin Eagles. Contact us for additional details. First Name Email Address Your Grill Brand (optional) Send My Coupon. About About Us Price Matching BBQ Learning Center Newsletter Easy Financing Become a Supplier Prof. Accounts Contact Us Support Order Status Account Return Policy Shipping Information FAQ’s Grill Services Miami Prop 65 Info Privacy Policy Terms Showroom 5881 Pembroke Road Hollywood, FL 33023 1-877-983-0451 Copyright The BBQ Depot, Inc. Regulator will not allow fuel in the line. Do not use a longer Natural Gas hose than is supplied with your grill. Outside temperatures will affect the amount of preheat time required.

Do not use a longer Natural Gas hose than is supplied with your grill. Do not use a longer Natural Gas hose than is supplied with your grill. Reduce temperatures according to type of foods being cooked. For the best experience on our site, be sure to turn on Javascript in your browser.Watch our video on how to identify your gas grill's model number. View the common product identification tag locations diagram. Consult your Owner's Manual if you still cannot locate your model number. Please browse our catalog below for the most up-to-date selection of Coleman BBQ parts. If you can’t find a part, just contact our friendly customer care team. Subscribe to our Newsletter. Recieve promotions, grill maintenance tips, and recipes. SIGN UP All Rights Reserved. Privacy Policy. Keep this manual for future reference. IfThe handling, storage andHandling of Liquified Gases, or. CSA B149.1, Natural Gas and. Propane Installation Code.For Outdoor Use Only. The owner shall post in aGeneral Safety Information. General Installation. Portable L.P. Gas Barbecue Cylinders. L.P. Gas Cylinder. Hose and Regulator. Transporting the Cylinder. Filling and Purging Type 1 L.P. Gas Cylinders. Purging and Evacuating Devices for L.P. Gas CylindersTo Set up. Leak Testing. Fixing a Fuel Leak. Start-up Check List. Lighting the Grill. General Use and Correct Burner Flames. Cleaning the Venturi. Storage. Maintenance. Things You Should Know. Troubleshooting. Replacement Parts List. WarrantyGeneral Safety Information. This manual contains important information about the assembly, operationGeneral safety information isParticular attention should be paid to information accompanied by theKeep this manual for future reference and to educate new users of thisSafety precautions are essential when any mechanical or propane fueledThese precautions are necessary when using, storing, and servicing.

Channel on Center Lid.CatchFor easier removal, rotate the tank out of the upper tank support, then removeSecure the Tank Mounts as shown.GoodYellowL.P. cylinders. DO NOT touchBlue. Blue. Holes in Burner. Cleaning the VenturiOne View Port for each of the six. Valve Orifices is located underneath the grill as shown in Fig. 16. Remove the grease trays to reveal the six View Ports.Note:These nests can obstruct gas flowSuch a fire canTo help preventNOTE: Water or air pressure will notSteps For Cleaning Venturi:Once the oil has burned away, check the burner flame perThe Burner Flame. Keep the cooking surfaces in place. Observe the burner’s flame from above, through the grates. Flames should appear similar to the good flame shown in. Fig. 17 and as follows:A build-up of food deposits, fatsClean the burner to remove residue and check for cloggedSome units will heat somewhat more to the center and back of grill. Flavor of grilledIf stored indoors, detach and leaveRefer to Chapter 5 of Standard for. Follow all localMaintenanceTo enjoy years of outstanding performance from your grill, perform the following maintenance activities on a regular basis. Never use flammable or abrasiveKeep controls, burner and circulating airClean burner with warmFrequently check for corroded areasThe Coleman Company, Inc. Things You Should KnowTroubleshooting. Problem. Possible Cause. Solution. Burner won’t light. Gas pressure is low. Cylinder is empty. Replace cylinder. Air in gas line. Burner may take up to one minute to lightIgniter is wet. Light the grill with a match. Burner won’t stay lit. Burner flame is low. Gas pressure is low. Replace cylinder. Use a full cylinder. Fuel flow is restricted. Check burner and orifices for blockage. Adjust controlFuel flow is restricted. Excessive yellow flames. Check burner, orifices and venturi for blockage (bugs,Improper FlameParts List. No. Part No. DescriptionEnd Lid. Grease Pan. Center Lid Assembly. Igniter Module.

Hose AssemblyColeman Limited One-Year Warranty. The Coleman Company, Inc. (“Coleman”) warrants that for a period ofColeman, at its option, will repairReplacement will be made with a newIf the product is no longerThis warranty is valid for the original retail purchaser from the date ofKeep the original sales receipt. Proof of purchase is required to obtain warranty performance. ColemanThis warranty does not cover normal wear of parts or damage resultingFurther, the warranty does not cover Acts of God, suchYou can findTDD 316-832-8707 in the United States. If a service center is notCarefully package the product and sendFor products purchased in the United States. The Coleman Company, Inc.Wichita, KS 67219. Do not mail products with fuel in tanks, or with disposable propaneThe Coleman Company, Inc.Wichita, KS 67219 U.S.A. Consumers should check with recalling firms for further details. Consumers should stop using recalled products immediately unless otherwise instructed. It is illegal to resell or attempt to resell a recalled consumer product. This can pose a fire or explosion hazard. Coleman has received no reports of injuries or property damage. The model name and number can be found directly on the front of the grills and on the inside cover of the heaters. Once the regulator is replaced, the grill or heater may be used. CPSC’s work to ensure the safety of consumer products has contributed to a decline in the rate of deaths and injuries associated with consumer products over the past 40 years. CPSC does not control this external site or its privacy policy and cannot attest to the accuracy of the information it contains. You may wish to review the privacy policy of the external site as its information collection practices may differ from ours. Linking to this external site does not constitute an endorsement of the site or the information it contains by CPSC or any of its employees. Certain gas regulator assemblies fitted may leak propane.

The apparent cause of the leak is an improper seal within the body of the regulator assembly. Risk of fire or explosion. Stop using your BBQ and contact Coleman Brands on 1800 330086.