ftr 3050 service manual

Some people remove that for cleaning, which I never heard of doing in training and sounds ridiculous to me to do. The next stop after the L Mirror is past the shutter and the removable plastic lens that you can take out of the side of the machine. So, another thing that happens before and during exposure, as the spin motor reaches speed and laser comes on, is that the laser light is sweeping across the width of the film, and the spin motor is acting as an encoder, but for a synching pulse, the light hits a small shiny metal surface, off the edge of the largest film size, and reflects down to a detector. You might be starting up and this pulse cannot be detected, hence Error 15. There is a trap door where you can access this sensor, sort of, and at least see it, and see light reflected onto it. If it were intermittent, I would recommend cleaning the sensor on the board. It's a small sensor, flat square plastic, near the end of the board. If you observe this on your machine, you might see the light missing this sensor. I wouldn't recommend moving the ASens board if it looks like something else were moved. That would be a last ditch effort. If that worked, all bets would be off as far as image quality, size, distortion, etc. So right now, that current ASens position is your best bet for getting any other optics back in position. Good luck. The service engineer from UK spent long hours on it before he could set it aright. Please elaborate on your last statements concerning using Current Asens position as a reference point to fix other optics. Cheers So we shouldn't be quick to move the sensor position. Try to see what else might have been moved, and also in the cleaning, that the far edges of the mirror are clean as well as the middle, because that part of the light path is important for this function. I will say i am on holiday now till June. I will try your suggestion and get everybody posted on the outcome.Cheers Mostly are LD unit problem.

• ftr 3050 service manual, ftr 3050 service manual pdf, ftr 3050 service manual download, ftr 3050 service manual free, ftr 3050 service manual online.

For a better experience, please enable JavaScript in your browser before proceeding. It may not display this or other websites correctly. You should upgrade or use an alternative browser. If you think you can use it, let me know. There is Key sequence Like in FTR-5055.Can you help in this matter. Thanks and best regards Swarna If you think you can use it, let me know.I am looking for FTR 3050 machine. Hi, I am looking to purchase Screen FTR 3050, Katana 5050 Machines, Please contact me asap if you have one available.Send me your contact information.The advantages can put money on your bottom line. So what’s your next step? You should upgrade or use an alternative browser. The film is not exposed to the laser ray. I have the service manual but I am interested in the service manual for the online processor. My processor is always on the NOT READY state. Different board, laser, etc. You likely need a service call. The processor is not related.The film is not exposed to the laser ray. My processor is always on the NOT READY state.Your problem on your FTR-3050 imagesetter machine are related to this parts. 1. Guard, OPTV or Cont Board 3 2. Laser Diode Unit 3. Asen Board positioning If there are people knowledgeable, you can unplug and plug the connectors from the cont board unit If problem still arise call a service engineer to check your machine. The error message pops up when the machine is about to expose the film. The problem is not with the boards or the diode. The error message came up when i cleaned the optics. Probably the optics positions had been misaligned. The local engineer could not solve the problem I called Screen UK they ask me to call somebody in Kenya who cover my area Nigeria. I had similar problem once on another FTR-3050 years back but was fixed by a screen trained engineer from UK. That option is expensive now. They're all fixed pretty well, but maybe the long L mirror moved in it's bracket.

To purchase a catalog online, please add the product to your cart, fill in the contact form online. Our managers proceed your order the same day. It's a diagnostic system designed for Allison Product Families' transmissions. The scan tool is available with worldwide shipping. Order the latest version with worldwide shipping or Download. Please read instructions prior to Upgrade. Bulletin Only. Box connector enablement. Bulletin Embedded PLEASE READ INSTRUCTIONS PRIOR TO UPGRADE Box connector enablement. Bulletin Embedded PLEASE READ INSTRUCTIONS PRIOR TO UPGRADE For use with Sharp Driver Please download relevant Request to reset Form below Zipped file containing all. You can print, zoom or read any diagram, picture or page from this Service Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Kyocera TASKalfa 3050ci TASKalfa 3550ci TASKalfa 4550ci TASKalfa 5550ci photocopier. You can find easily everything what do you need. To see what contain, please read table of contents. Search Search 700P86580December 1997 NOTICEWhile every care has been taken in the preparation of this mantlal, no liability will be accepted by Xerox Engineering Systems arising out of any inaccuracies or omissions. XEROX, and 3050 are trademarks used by Xerox Canada Ltd.Page Introduction. vii About This Manual. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions. To install your download click on the name of the downloaded file.Canon Authorized Dealers provide the highest quality service and are supported by Canon-certified technicians using Canon Genuine parts. Please contact your Canon Authorized dealer for all your service needs. Need to find a dealer?

There's a technique on how to check the laser diode using your digital tester but problem this is a secret for some of us. Hint: error appear if ASEN position left and right was not reach by the laser beam.ASEN and OPTV board might damage in power fluctuation or the power supply is not original from the dainippon screen. Very need it Thanks in advance The advantages can put money on your bottom line. Discover everything Scribd has to offer, including books and audiobooks from major publishers. Start Free Trial Cancel anytime. Sometimes it's really helps, enjoy! Full description Save Save kyocera service manual 3050 4050 5050 For Later 100% 100% found this document useful, Mark this document as useful 0% 0% found this document not useful, Mark this document as not useful Embed Share Print Download Now Jump to Page You are on page 1 of 455 Search inside document Check w ith your local solid waste officials for details in your area for proper disposal. Verifiez avec les fonc- tionnaires municipaux de votre region pour les details concernant des dechets solides et une mise au rebut appropriee. Browse Books Site Directory Site Language: English Change Language English Change Language. Service Manual In ML-305X, the paper path is consisted of 250 sheets Cassette containing friction Pad, pickup-roller, feed-roller for functioning as registration, Earth-transfer for guiding the transfer inlet, Guide-Tr for guiding sheets between transferring and fixing, Fuser, Exit Assy. In ML-305X, the driving device is consisted of f55 BLDC motor, OPC, Pick-up, Feed, Gear-Train connected with Mounting member. All trademarks and copyrights in the published materials belong to their respective owners. Electronic workshop manual helps you to carry out installation or removal of any parts. After the purchase of electronic products, we provide after-sales service user, will send all the necessary installation instructions.

PeerelessPrintXL is a trademark of Peerless Systems Corporation (2381 Rosecrans Ave. Kyocera Mita Corporation is using these fonts under agreements with the Japanese Standards Association. All other brands and product names are registered trademarks or trademarks of their respective companies. OpenSSL License Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.If you need to have access to the fonts on more than three printers, you need to acquire a multi-user license agreement which can be obtained from Monotype Imaging. Monotype Imaging retains all rights, title and interest to the Software and Typefaces and no rights are granted to you other than a License to use the Software on the terms expressly set forth in this Agreement.

Number of Concurrent Connection: SMB: 32, WebDAV: 12 (Active Sessions) Advanced Box Features: Disabling Advanced Box, Storage Filtering, Authentication for Advanced Box Log-in, Sort Function, Printing a PDF File with a Password, imageWARE Secure Audit Manager Support Memory Media Standard: USB Memory Optional: SD, SDHC, CompactFlash, Memory Stick, MicrodriveBond to 110 lb. Index Special Media Support Tracing, Labels, Transparency, Tab, and EnvelopesBond to 32 lb. Bond Two-sided Scanning: 13 lb. Bond to 32 lb. BondBond) 100 SheetsBond) Lower Tray: 100 Sheets (20 lb. Bond)Bond - 21 lb. Bond) 30 Sheets (22 lb. Bond - 28 lb. Bond) 2 Sheets (29 lb. Bond - 140 lb. Index) 11 x 17, Legal, Letter-R: 30 Sheets (14 lb. Bond - 21 lb. Bond) 20 Sheets (22 lb. Bond - 28 lb. Bond) 2 Sheets (29 lb.Bond to 21 lb. Bond) 30 Sheets (22 lb. Bond to 28 lb. Bond) 2 Sheets (29 lb. Bond to 140 lb. Index) 11 x 17, Legal, Letter-R: 30 Sheets (14 lb. Bond to 21 lb. Bond) 20 Sheets (22 lb. Bond to 28 lb. Bond) 2 Sheets (29 lb.Bond to 28 lb. Bond) (12 x 18, 11 x 17, Legal, Letter-R)Paper Capacity of Saddle-Stitch Mode: 25 Booklets (5-sheet Booklets)Bond to 21 lb. Bond) 30 Sheets (22 lb. Bond to 140 lb. Index) 11 x 17, Legal, Letter: 30 Sheets (14 lb. Bond to 28 lb. Bond) 2 Sheets (29 lb.The driver may be included in your OS or you may not need a driver. Recommended Driver(s) File Name Date File Size Optional Driver(s) File Name Date File Size Recommended Software File Name Date File Size Optional Software File Name Date File Size Recommended Manual(s) File Name Date File Size Optional Manual(s) File Name Date File Size. Please read this Operation Guide before you start using the machine, and keep it close to the machine for easy reference. In this Operation Guide, 3050, 4050 and 5050 are referred to as 30 ppm model, 40 ppm model and 50 ppm model respectively. Legal and Safety Information Please read this information before using your machine.

CAUTION: Indicates that personal injury or mechanical damage may result from insufficient attention to or incorrect compliance with the related points. Symbols The U symbol indicates that the related section includes safety warnings. Be sufficiently careful to avoid fire or electric shock when removing a paper jam or when replacing toner. High temperature inside. Do not touch parts in this area, because there is a danger of getting burned. Do not incinerate toner and toner container. Dangerous sparks may cause burn. Label inside the machine (Laser radiation warning) Moving parts inside. May cause personal injury. Do not touch moving parts.Such locations may cause the machine fall down or fall over. This type of situation presents a danger of personal injury or damage to the machine. Avoid locations with humidity or dust and dirt. If dust or dirt become attached to the power plug, clean the plug to avoid the danger of fire or electrical shock. Avoid locations near radiators, heaters or other heat sources, or locations near flammable items to avoid the danger of fire. To keep the machine cool and facilitate changing of parts and maintenance, allow access space as shown below. Install in an air-conditioned room and avoid the following locations when selecting a site for the machine.During copying, some ozone is released, but the amount does not cause any ill effect to one’s health. If, however, the machine is used over a long period of time in a poorly ventilated room or when making an extremely large number of copies, the smell may become unpleasant. To maintain the appropriate environment for copy work, it is suggested that the room be properly ventilated. Avoid multiple connections in the same outlet. These types of situations present a danger of fire or electrical shock. Plug the power cord securely into the outlet. If metallic objects come into contact with the prongs on the plug, it may cause a fire or electric shock.

Always connect the machine to an outlet with a ground connection to avoid the danger of fire or electrical shock in case of an electric short. If an earth connection is not possible, contact your service representative. Other precautions Connect the power plug to the closest outlet possible to the machine. Handling of plastic bags WARNING Keep the plastic bags that are used with the machine away from children. The plastic may cling to their nose and mouth causing suffocation.This type of situation presents a danger of fire or electrical shock should they fall inside. Do not remove any of the covers from the machine as there is a danger of electrical shock from high voltage parts inside the machine. Do not damage, break or attempt to repair the power cord. Do not place heavy objects on the cord, pull it unnecessarily or cause any other type of damage. Never attempt to repair or disassemble the machine or its parts as there is a danger of fire, electrical shock or exposure to the laser. If the laser beam escapes, there is a danger of it causing blindness. If the machine becomes excessively hot, smoke appears from the machine, there is an odd smell, or any other abnormal situation occurs, there is a danger of fire or electrical shock. Turn the main power switch off immediately, be absolutely certain to remove the power plug from the outlet and then contact your service representative. If anything harmful (paper clips, water, other fluids, etc.) falls into the machine, turn the main power switch off immediately. Next, be absolutely certain to remove the power plug from the outlet to avoid the danger of fire or electrical shock. Then contact your service representative. Do not remove or connect the power plug with wet hands, as there is a danger of electrical shock. Always contact your service representative for maintenance or repair of internal parts. OPERATION GUIDE xiii Legal and Safety Information CAUTION Do not pull the power cord when removing it from the outlet.

3 To protect proprietary rights of Monotype Imaging, you agree to maintain the Software and other proprietary information concerning the Typefaces in strict confidence and to establish reasonable procedures regulating access to and use of the Software and Typefaces. 4 You agree not to duplicate or copy the Software or Typefaces, except that you may make one backup copy. You agree that any such copy shall contain the same proprietary notices as those appearing on the original. OPERATION GUIDE Legal and Safety Information 5 This License shall continue until the last use of the Software and Typefaces, unless sooner terminated. This License may be terminated by Monotype Imaging if you fail to comply with the terms of this License and such failure is not remedied within thirty (30) days after notice from Monotype Imaging. When this License expires or is terminated, you shall either return to Monotype Imaging or destroy all copies of the Software and Typefaces and documentation as requested. 6 You agree that you will not modify, alter, disassemble, decrypt, reverse engineer or decompile the Software. 7 Monotype Imaging warrants that for ninety (90) days after delivery, the Software will perform in accordance with Monotype Imagingpublished specifications, and the diskette will be free from defects in material and workmanship. Monotype Imaging does not warrant that the Software is free from all bugs, errors and omissions. The parties agree that all other warranties, expressed or implied, including warranties of fitness for a particular purpose and merchantability, are excluded. 8 Your exclusive remedy and the sole liability of Monotype Imaging in connection with the Software and Typefaces is repair or replacement of defective parts, upon their return to Monotype Imaging. Further use, duplication or disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR 52.227-19 (c)(2).

12 You acknowledge that you have read this Agreement, understand it, and agree to be bound by its terms and conditions. Neither party shall be bound by any statement or representation not contained in this Agreement. No change in this Agreement is effective unless written and signed by properly authorized representatives of each party. By opening this diskette package, you agree to accept the terms and conditions of this Agreement. OPERATION GUIDE vii Legal and Safety Information Energy Saving Control Function The device comes equipped with Sleep where printer and fax functions remain in a waiting state but power consumption is still reduced to a minimum when there is no activity with the device within a set amount of time since the device was last used. Sleep The device automatically enters Sleep when 8 minutes have passed since the device was last used. The amount of time of no activity that must pass before Sleep is activated may be lengthened. For more information see Sleep and Auto Sleep on page 3-4. Automatic 2-Sided Copy Function The Energy Star Program encourages the use of 2-sided copying which reduces the load on the environment and this device includes 2-sided copying as a standard function. For example, by copying two 1-sided originals onto a single sheet of paper as a 2-sided copy, it is possible to lower the amount of paper used. For more information see Duplex Copying on page 3-14. Paper Recycling The Energy Star Program encourages the use of recycled paper which reduces the load on the environment and this device supports recycled paper. Your sales or service representative can provide information about recommended paper types.The symbols and their meanings are indicated below. WARNING: Indicates that serious injury or even death may result from insufficient attention to or incorrect compliance with the related points.

If the power cord is pulled, the wires may become broken and there is a danger of fire or electrical shock. (Always grasp the power plug when removing the power cord from the outlet.) Always remove the power plug from the outlet when moving the machine. If the power cord is damaged, there is a danger of fire or electrical shock. Always hold the designated parts only when lifting or moving the machine. For safety purposes, always remove the power plug from the outlet when performing cleaning operations. If dust accumulates within the machine, there is a danger of fire or other trouble. It is therefore recommended that you consult with your service representative in regard to cleaning of internal parts. This is particularly effective if accomplished prior to seasons of high humidity. Consult with your service representative in regard to the cost of cleaning the internal parts of the machine. Other precautions Do not place heavy objects on the machine or cause other damage to the machine. Do not open the front cover, turn off the main power switch, or pull out the power plug during copying. When lifting or moving the machine, contact your service representative. Do not touch electrical parts, such as connectors or printed circuit boards. They could be damaged by static electricity. Do not attempt to perform any operations not explained in this guide. Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not look directly at the light from the scanning lamp as it may cause your eyes to feel tired or painful. This machine comes equipped with an HDD (hard disk drive). Do not attempt to move the machine while the power is still on. Since any resulting shock or vibration may cause damage to the hard disk, be sure to turn off the power before attempting to move the machine.It is recommended that important data be backed up on a PC or other media.

Be also sure to store originals of important documents separately. If using the optional Data Backup Kit, received fax data on the HDD can be stored here and prevent accidental loss of data. Cautions when handling consumables CAUTION Do not attempt to incinerate the toner container or the waste toner box. Dangerous sparks may cause burns. Keep the toner container and the waste toner box out of the reach of children. Do not attempt to force open or destroy the toner container or the waste toner box. Do not turn off the main power switch, but press the Power key on the operation panel to enter Sleep mode. Other precautions Return the exhausted toner container and waste toner box to your dealer or service representative. The collected toner container and waste toner box will be recycled or disposed in accordance with the relevant regulations. Store the machine while avoiding exposure to direct sunlight. OPERATION GUIDE xv Legal and Safety Information Store the machine in a place where the temperature stays below 40?C while avoiding sharp changes of temperature and humidity. If the machine will not be used for an extended period of time, remove the paper from the cassette and the Multi Purpose (MP) Tray, return it to its original package and reseal it.This indicates that the product is safe to use during normal operation and maintenance. The laser optical system, enclosed in a protective housing and sealed within the external covers, never permits the laser beam to escape. 2. The CDRH Act A laser-product-related act was implemented on Aug. 2, 1976, by the Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration (FDA). This act prohibits the sale of laser products in the U.S. without certification, and applies to laser products manufactured after Aug. 1, 1976. The label shown below indicates compliance with the CDRH regulations and must be attached to laser products marketed in the United States.

On this machine, the label is on the right. OPERATION GUIDE 3050 4050 5050 COPYING MACHINE 120V 60Hz 11.5A COPYING MACHINE 120V 60Hz 11.5A COPYING MACHINE 120V 60Hz 11.5A MACHINE No.PPH MACHINE No.PPJ MACHINE No.PPK MANUFACTURED MANUFACTURED MANUFACTURED FCC ID:E52B5J0151 Contains IC:1059B-B5J0151 FCC ID:E52B5J0151 Contains IC:1059B-B5J0151 FCC ID:E52B5J0151 Contains IC:1059B-B5J0151 MADE IN CHINA MADE IN CHINA MADE IN CHINA xvii Legal and Safety Information 3. Optical unit When checking the optical unit, avoid direct exposure to the laser beam, which is invisible. Shown at below is the label located on the cover of the optical unit. 4. Maintenance For safety of the service personnel, follow the maintenance instructions in the other section of this manual. 5. Safety switch The power to the laser unit is cut off when the front cover is opened.Other switches on the equipment are only functional switches and are not suitable for isolating the equipment from the power source. Attention: Le debranchement de la fiche secteur est le seul moyen de mettre l’appareil hors tension. Les interrupteurs sur l’appareil ne sont que des interrupteurs de fonctionnement: ils ne mettent pas l’appareil hors tension. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. CAUTION — The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.

Radio Tag Technology In some countries the radio tag technology used in this equipment to identify the toner container may be subject to authorization and the use of this equipment may consequently be restricted.In the event the MFP or an accessory is found to be defective within the warranty period, Kyocera's only obligation and the Customer's exclusive remedy shall be replacement of any defective parts. Kyocera shall have no obligation to furnish labor. 2. This warranty is valid only for the original retail purchaser (referred to as the “Customer”) of a new Kyocera MFP in the United States of America or Canada, based upon the country of purchase. 3. In order to obtain performance of this warranty, the Customer must immediately notify the Authorized Kyocera Dealer from whom the product was purchased. The Customer may also have other rights, which vary from state to state, or province to province. Neither the seller, nor any other person, is authorized to extend the time period, or expand this warranty on behalf of Kyocera. 7. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES AND CONDITIONS, EXPRESS OR IMPLIED, AND KYOCERA SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.Chapter 1 - Part Names Identifies machine parts and operation panel keys. Chapter 2 - Preparation before Use Explains adding paper, placing originals, connecting the machine, and necessary configurations before first use. Chapter 3 - Basic Operation Describes the procedures for basic copying, printing and scanning. Chapter 4 - Optional Equipment Introduces the convenient optional equipment available for this machine. Chapter 5 - Maintenance Describes cleaning and toner replacement. Chapter 6 - Troubleshooting Explains how to handle error messages, paper jams and other problems. Appendix Explains how to enter characters, and lists the machine specifications.

OPERATION GUIDE xxi About this Operation Guide Included Guides The following guides are supplied with the machine. Refer to them as necessary. Operation Guide (This Guide) Describes how to load paper, basic copy, print and scan operations, and troubleshooting. Advanced Operation Guide Explains copying, printing and scanning features in depth, as well as default settings. Conventions in This Guide The following conventions are used depending on the nature of the description. Convention Example Bold Indicates the operation panel keys or a computer screen. Ready to copy is displayed. Used to emphasize a key word, phrase or references to additional information. For more information refer to Sleep and Auto Sleep on page 3-4. Note Indicates supplemental information or operations for reference. NOTE: Important Indicates items that are required or prohibited so as to avoid problems. IMPORTANT: Indicates what must be observed to prevent injury or machine breakdown and how to deal with it.For further details, refer to the page detailing that function or source tray. OPERATION GUIDE About this Operation Guide Icons on the Touch Panel The following icons are used to indicate originals and paper placement directions on the touch panel. Documents Advanced Operation Guide KX Driver User Guide Network FAX Driver Operation Guide COMMAND CENTER Operation Guide KM-NET for Clients Operation Guide KM-NET for Direct Printing Operation Guide Scan to SMB(PC) Setup Guide PRESCRIBE Commands Technical Reference PRESCRIBE Commands Command Reference 2-2 OPERATION GUIDE Preparation before Use Determining the Connection Method and Preparing Cables Check the method to connect the equipment to a PC or network, and prepare the necessary cables. Connection Example Determine the method to connect the equipment to a PC or network by referring to the illustration below.